Search Results

In this paper, spray characteristics were examined to deduce the effect of ambient gas properties. Considered ambient properties were the viscosity μa and density ρa, and thus the kinematic viscosity νa. The objective of this paper is to reveal the effect of compressibility of the ambient gas to spray formation. In the experiments, the changed ranges were And a standard-sac volume nozzle of hole diameter dn =0.25 mm (ln/dn=3.0) was used at constant injection pressure difference (Δp=16.2 MPa). Also the injection pressure was varied in the range of 55 to 120 MPa with a mini-sac volume nozzle of hole diameter dn =0.20 mm (ln/dn =5.5). Several different gases were used to change the ambient viscosity at a room temperature. From the experiments, it is obtained that larger the viscosity, the more the spray spreads in the radial direction, thus the spray angle gets larger and the tip penetration became shorter.

We propose a new concept on simultaneous reduction of NO and soot emissions in Diesel engine exhaust by the diesel fuel oil (n-Tridecane) with liquefied CO2 dissolved. The CO2 dissolved fuel is expected to undergo flash boiling or gas separation when being injected into the combustion chamber and improve spray atomization and mixing process both of which are primary factors to govern soot formation. Also the internal EGR effect caused by CO2 injected with the fuel is expected to NO formation. In order to assess this concept, combustion experiments were carried out using a rapid compression and expansion machine. Thus, flame characteristics and heat release rate were analyzed for the combustion process of diesel fuel and CO2 mixed fuel. And, it is revealed that the diesel fuel-liquefied CO2 mixed fuel can successfully reduce NO emission in a diesel combustion system.

It is very significant to take the intermediate products in diesel combustion for understanding the generation of exhaust emissions like SOF, dry soot and so on. The products generated in a constant volume combustion chamber were sampled by pricking a sheet of polyester film installed in the chamber to freeze the chemical reaction. The gas was analyzed by a gas chromatography. The fuel used was n-heptane. It is able to explain the generation of exhaust emissions by the experimental results. The other objective is to simulate the intermediate products. It is capable of explaining the relation between the simulated and experimental results.

Almost all the researches relating to the characteristics of transient spray have carried out by using the fuel with only single component. However, the actual fuel oil supplying to a reciprocating engine has multiple components. Thus, this paper describes the experimental results on the characteristics of a transient spray formed by the mixed fuel with three kinds of pure fuel. The state of periphery of non evaporating spray near the nozzle outlet was arranged by the dimensionless number. And the technique of laser Induced fluorescence (LIF) was applied to an evaporating spray to find the state of mixing.

This paper describes the soot behavior in a diesel flame. The experiments were carried out in a constant volume chamber with quiescent atmosphere. Parameters were the ambient temperature and the oxygen concentration. The integrated image of flame was taken, the natural emission of flame was detected and the KL factor was found by means of classical technique of laser light extinction. The results were discussed by use of the apparent rate of heat release. As a result, the ignition delay and the vortex with large scale generated in a diesel spray affect the soot behavior in a diesel flame.

The authors carried out a basic and systematic investigation on diesel combustion processes using three different experimental apparatuses. This paper summarized the experimental results obtained from the three devices. Among the data contained in this paper are; (1) The structure and shape of diesel spray, the air movement around diesel spray and the spatial and temporal distributions of the size of droplets in diesel spray injected into the high pressure and room temperature charge. (2) The shape of diesel spray injected into the high pressure and high tempertaure charge. (3) The characteraistics of flame, and illumination delay, and ignition delay in the high pressure and high temperature charge.

As authors reported in SAE Trans. 800968, entitled “Investigation on the Characteristics of Diesel Fuel Spray”, the flame never proceeds into the initial-part of the spray during injection. The length of the initial part-lies within 10 to 15 mm regardless of the conditions of the injection systems and of the ambient conditions. The ignition delay does not decrease but becomes constant when the ambient temperature or the pressure exceed a discrete value. The authors would like to propose a new concept of “Spray Formation Delay” during which the field is generated where the physical and chemical delay can exist. The spray formation delay is one of the major factors which control the above mentioned limitation of ignition delay. The characteristics of the spray formation delay are investigated and clarified.

This paper presents the experimental study on the characteristics of a transient gas jet. Helium was injected instantaneously into a quiescent atmosphere with constant pressure. The distributions of instantaneous static pressure, radial and axial velocities and concentration at measuring points in the jet, which is obtained by the statistical data processing, are discussed to explain a transient mixture formation in the jet. The analogy between this jet and a diesel spray as for this mixture formation are also discussed by using these results.

In a small high-speed DI diesel engine, injected fuel sprays impinge on the wall of piston cavity. Discussion and analysis of the combustion phenomena in the diesel engine demand the measurement of the characteristics of the impinging spray. In the experiments presented here, diesel fuel oil was injected into a high pressure chamber in which compressed air or CO2 gas at room temperature was charged. The single spray was impinged on a flat wall at a normal angle. The growth of the spray was photographed, not only with transmitted light but also with scattered light through a narrow slit. The temporal and spatial distribution of the droplets density in the impinging spray applying the concentric circle model was calculated using the data of the laser light extinction method. From these results, the detailed information concerning the droplets density in the impinging diesel spray was obtained.

In previous multi-dimensional modeling on spray dynamics and vapor formation, single component fuel with pure substance has been analyzed to assess the mixture formation. Then it should be expected that the evaporation process could be performed for the multicomponent fuel such as actual Gasoline and Diesel gas oil. In this study, vapor-liquid equilibrium prediction was conducted for multicomponent fuels such as 3 and 10 components mixed solution with ideal solution analysis and non-ideal solution analysis. And the computation of distillation characteristics was conducted for the steady state fuel condition fuel condition to understand the evaporation process. As a result, calculated distillation characteristics are consistent well with experiment results. And the evaporation process of a multicomponent droplet in the combustion chamber has been calculated with the variation of ambient pressure and temperature.

The combustion phenomena in an IDI diesel engine having a swirl chamber were detected by optical methods. The spatial and temporal distribution of the natural emission of OH radical was measured through the band pass filters and those of KL factor and flame temperature were obtained by the two-color method. As a consequence, the combustion phenomena are made clear by these experimental results.

In SI engines with port injection system, the injected fuel spray adheres surely on the port wall and the inlet valve, consequently, the spray-wall interaction process leads to the generation of unburned hydrocarbons and uncontrollable mixture formation. This paper deals with the fuel mixture preparation process including basic research on characteristics of the wall-wetted fuel film on a flat wall inside a constant volume vessel. In the experiments, iso-octane mixed with biacetyl as a tracer dopant was injected through a pintle type injector against a flat glass wall under the ambient conditions of atmospheric pressure and room temperature. The thickness of the adhered fuel film on the wall was quantitatively measured by using laser induced fluorescence (LIF) technique, which provides 2-D distribution information with high special resolution as a function of the injection duration, the impingement distance from the injector to the wall, and the impingement angle against the wall.

We propose a new concept on simultaneous reduction of NO and soot emissions in Diesel engine exhaust by use of the diesel fuel oil (n-Tridecane) with liquefied CO2 dissolved. The CO2 dissolved component is expected to undergo flash boiling or gas separation when being injected into the combustion chamber, and improve spray atomization and mixing process both of which are primary factors to govern soot formation. Further, the internal EGR effect caused by CO2 component injected with the fuel is expected for NO formation. In order to assess this concept, spray dynamics measurement was conducted in the constant volume vessel with a variation of ambient pressure and temperature. Further, combustion experiments were carried out by using a rapid compression and expansion machine. Here, characteristics of the evaporative mixed fuel spray were examined by shadowgraph photography.

OH radical generated in a DI diesel engine has a close relationship to soot oxidation. To clarify this fact, the distribution of the natural emission of OH radical was captured by means of an interference filter system and that of soot was detected by the simultaneous application of a laser induced incandescence (LB) and a laser induced scattering (LIS). The experiments were carried out in a small sized high-speed DI diesel engine installed with an optical access view. The generation of OH radical and the formation/oxidation of soot are discussed by using both images.

In previous our work, we revealed that the flash boiling process could improve remarkably the spray atomization for the pure substance-single component fuel in relation to the port-injected S.I. engines. Then, we applied this flash boiling spray to the Diesel spray process by the use of the two phase region formed between liquefied CO2 and n-Tridecane as the first step of fuel design concept. And the promoted atomization properties could be obtained in this mixed fuel concept. Further, we could obtain the simultaneous reduction of NO and soot emissions in Diesel engine exhaust due to the spray internal EGR effect and reburning of soot. As the second step, we proposed a novel fuel design concept for low exhaust emission and combustion control, relating to mixed and reformulated fuels with a lower boiling point fuel such as gasoline components or gas fuel and a higher boiling point fuel such as gas oil or heavy oil components to obtain the both advantages of their fuels for combustion.

In this study, characteristics of the development and auto-ignition/combustion of hydrogen jets were investigated in a constant-volume vessel. The authors focused on the effects of the jet developing process and thermodynamic states of the ambient gas on auto-ignition delays of hydrogen jets. The results show that the ambient gas temperature and nozzle-hole diameter are significantly effective parameters. By contrast, it is clarified that the ambient gas oxygen concentration has a weak effect on the auto-ignition/combustion of hydrogen jets. Consequently, it is supposed that the mixture formation process is capable of improving the auto-ignition/combustion of hydrogen jets.